Replacement UPVC Door Handles
You can find the ideal handle for your door, whether you are replacing your handles or adding extra security. The Upvc handles are simple to install and have the 92mm minimum center distance of multipoint locks.
The backplate fixing centre and the lever/keyhole dimensions are the most important measurements. Compare these measurements with your current marks before placing an order.
Lever/Pad
Lever pad handles are made up of a lever on one side, and a paddle-shaped handle on the opposite. They are intended for use with key wind locks. However they can also be attached to multipoint split spindle door locks.
Our range of upvc handles lever pads are available in a wide range of finishes. They will be displayed in the drop-down menu after you have identified the perfect handle for your doors. Not all styles of handles are available in every finish and you should always check the sizes and technical drawings for the specific product that you want to make sure that you get the right size and fit.
When selecting new lever pad door handles made of upvc, it is important to ensure that they correspond to the PZ (distance between the handle spindle and the centre of the cylinder hole) of your current multipoint door locks, as these need to be in line for the doors to remain locked, either from the inside or outside. Our handles are designed to fit the majority of conventional cylinders, but it is always worth double-checking before ordering.
If you wish to upgrade to dual spindle levers, you'll need to remove the existing handles and take apart the lock case. This will require an extra split inline cylinder. You can purchase these separately. We have included a technical diagram in the images of each product.
It is a good thing to loosen the screws holding the door handle you have and then examine the mechanism. If the screws aren't tight enough it is possible to loosen them even more. Then you can remove the spindle from the handle and replace it with a new Upvc handle. It is important to ensure that the handle is in the correct position before installing it. You can do this by placing your finger between the door frame, and the handle to ensure that it's level.
Lever/Lever
Lever door handles operate a multi point lock using a Euro Cylinder and are found on the majority of double doors made of upvc, aluminum doors and some wooden doors. They are equipped with a lever on the inside and a paddle on the outside and are usually supplied in two different types. Sprung - These have an internal spring cassette within the backplate, which helps bring the handle lever into a horizontal position. Non-sprung: These do not have a mechanism for bringing the handle lever into a horizontal position.
To fix the door handle of a lever that is sagging, you will need to locate the detent access hole or pin, which is usually a small round or rectangle shaped hole or protruding pin located on one side of the handle base plate. Once you have located it, loosen the set screw with the help of a screwdriver, and then take it off to allow the lever to return to its horizontal position.
When the handle is in a horizontal position you can put the screws back in place and tighten them so that the handle stays secured to the base plate. You should also consider applying a threadlocking adhesive to the screw threads to improve the grip and prevent them from loosing over time.
There are a myriad of reasons that door handles for levers slide. The most common cause is that the fixings are too tight which causes the lever bearing to get tangled up against the door. It could also be due to the fact that the levers aren't being operated in a straight line and this is compressing the latch mechanism and preventing it from fully springing back into action.
A common cause of spring levers that are not functioning properly is the spring not being in the proper position on the backplate. To check whether the handle has returned to horizontal, simply move it.
door handle replacement exeter repairmywindowsanddoors is important to fix any loose door handles as soon as possible. This can cause excessive wear on the screws, and the handle might fall off the base plate. It is recommended to tighten all loose screws regularly, as this will help to prevent them from loosening.
Lever/Snib
These handles made of upvc are called "Snib handle sets" and have an snib lock button located at the top of the lever. If you do not have a dummy locking device you can use this to lock the door. These handles are fitted with the Fullex lock 68PZ. (68mm between spindle and the lock centre). We also have a selection of 68PZ door handle from manufacturers such as Ferco and Fab & Fix.
You can upgrade your home by changing the door handles whether you are replacing existing handles or installing new ones on doors you've built. There are a variety of styles available for door handles made of upvc including the traditional lever on the backplate. Other options include straight or curly short latches, as well as dummy knobs for multi-point locks. These are ideal for French doors.
Lever on backplate handles are often rectangular in shape, however there are also circular or oval shaped models that are referred to as rose door handles. These types of door handles have a lever or knob on a backplate, which sits behind the lever or knob and is sometimes referred to as the rosette, however some back plates can be detached to allow for concealed fixing.
There's a wide selection of chrome and coloured finishes available for these handles that complement your door and other hardware, including hinges, knobs, bolts and so on. Some handles come with grub screws to aid in the secure attachment of the lever or knob to the spindle. Other handles are supplied with bathroom spindles that can be used to operate bathroom locks. They feature a thumbturn turn as well as a release mechanism, perfect for bathroom doors.
Mortise
The tubular latch is the most likely to be the cause if your uPVC door handle is stuck open. It could be due to many things but the most prevalent is the lack of lubrication on the latch plate. It is possible to fix this issue by opening the door and spraying lubricant onto the handle and locking. Alternatively, it could be that the latch plate is detached from the backplate. This is a more complicated problem that would require the assistance of a specialist.
A multipoint handle system is the ideal solution for stuck door handles. These handles are mounted through the faceplate, and are operated by either a thumb turn or key knob that activates the cam that locks the deadbolt. The handles are available in a range of sizes that will fit different types of uPVC doors. They are also available with a variety of attractive finishes to complement the existing hardware. These handles are available via the internet or at the local locksmith. They are easy to install and come with clear instructions.
To choose a replacement handle set, you'll need to determine the PZ dimension of your cylinder. This is the distance in millimetres between the inside edge of the door frame and the centre of the handle hole. You will also need the type of lock that is installed on your door, irrespective of whether it's a mortise or hook lock. The easiest way to find the right handles once you have the measurements is to use the brand filter on the website. This will narrow down the options and you can then choose the right size from the list.
A typical handle set comprises the handle unit comprising two screws of different lengths, drill guides and instructions for installation. The smarter models, like the Igloohome Smart Mortise 2+, include the complete mortice lock, which has an integrated keypad. These are more complicated units that are best designed for professional installers or highly competent DIYers. Certain handle sets come with an array of other accessories, like weather strips, which can be used to improve the appearance of the door.